JimR Discussion starter · Apr 19, 2019. So I wheeled my D160 out of the shed to check things over, do an oil change, grease it, etc... before the mowing season starts. It won't run. The engine turns over fine and it will fire up for a few seconds if I shoot starting fluid down the carb throat. But it won't fire up on it's own with a (near ...Report to Moderator. Posted: Thu Nov 21, 2019 6:06 am Post subject: Re: JD 60 won't start. Try a set of Auto-lite 386 spark plugs and check the manifold gasket. The intake section of the manifold could have a leak. Try spaying carb cleaner in the center section of the manifold mounting area with the tractor running.May 15, 2011 · John Deere won't shut off!!! Hello everyone, I'm new here and did some searching but came up dry. Ok heres my issue. I have a John Deere 111 11hp B&S 5sp. Ive had a no start issue for some time now. I bought a new coil, and still no spark. I checked all the wiring connections for corrosion/loose, cleaned them up added some die electric grease. Mar 26, 2018 · J. Jonnyd Discussion starter · Mar 26, 2018. Hi All, I'm having trouble starting my 5420. The issue started out intermittently where it would fire when turned over and the shutdown immediately. Eventually after a couple of tries or after starting it with the throttle raised it would continue to run and act normal. 2019 1025R, iMatch quick hitch, John Deere Ballast Box, Frontier RC2048 rotary cutter, Titan pallet forks, Bro-tek wheel spacers, Frontier AF10F snow plow, Heavy Hitch tooth bar, Tractor PTO link, Ken’s bolt on hooks, Ken’s chain box, CTA grapple, Summit diverter.If all that is correct, the problem may well be with the clutch itself and may require a tractor split for repair. On the other hand, the external PTO levers and linkage on many tractors of that series (00, 03, 05, 10) have been changed and improved many times over the course of production with the 00 being the earliest.Sep 7, 2017 · Another good test to isolate the key switch/harness wiring from the battery/starter system is to jump the solenoid to engage the starter. Do this: 1) Disconnect small solenoid wire from the starter. 2) turn key to run position. 3) using a conductor, jump the starter motor battery terminal to the solenoid terminal. Another good test to isolate the key switch/harness wiring from the battery/starter system is to jump the solenoid to engage the starter. Do this: 1) Disconnect small solenoid wire from the starter. 2) turn key to run position. 3) using a conductor, jump the starter motor battery terminal to the solenoid terminal.Oct 31, 2017 · If all that is correct, the problem may well be with the clutch itself and may require a tractor split for repair. On the other hand, the external PTO levers and linkage on many tractors of that series (00, 03, 05, 10) have been changed and improved many times over the course of production with the 00 being the earliest. Jun 26, 2014 · John Deere 314 won't move forward or reverse. I recently purchased a 314 with the Kohler K321AQS engine. When I picked up the tractor the battery was dead, it didn't turn over, it didn't do anything. Installed a new battery cleaned up the carb and she fired right up. When I engage the hydro to move forward or reverse the tractor doesn't move it ... Posted: Fri May 04, 2018 11:17 am Post subject: Re: Power loss and will not rev up. Check the fuel shutoff under the tank. Normally a clogged check valve in the inj. pump return el will cause the tractor to die. almost immediately after startup. Retainer ring particles could be sticking the.Dec 12, 2006 · Loader Won't Lift. My father-in-law has a JD 790 with a 419 loader that i've been using to move some dirt around. The loader just up and quit lifting, though the bucket will curl and the three-point works fine. There's fluid going to the barrel side of the rams, but not to the shaft sides. My father-in-law said this happened once before and ... The battery must be healthy and fully charged, all connections tight and not heating up. Not sure how you have the starter circuitry wired, but if it uses a solenoid and the key switch, there may be a wiring problem or a bad ignition switch. Posted: Sun Apr 19, 2020 3:07 am Post subject: Re: John Deere A won t crank.Another good test to isolate the key switch/harness wiring from the battery/starter system is to jump the solenoid to engage the starter. Do this: 1) Disconnect small solenoid wire from the starter. 2) turn key to run position. 3) using a conductor, jump the starter motor battery terminal to the solenoid terminal.If you've been out using your tractor and all of a sudden it dies and won't restart, or, if you parked the tractor and left it for awhile and now you're back and it won't start, this video...My X540 lawn tractor wouldn’t start this spring and these are the steps I worked through to ultimately solve my problem. I think trying to jump start the dea...Posted: Fri Apr 30, 2021 9:56 am Post subject: 630 did run - now won't start. Long time listener, first time caller -. I have my grandfather's 1959 630 that I got running over the winter. Rebuilt the carb, got a new vacuum sediment bowl, plugs, plug wires, coil,The rate of drop knob is located just above the floor boards directly below the operators seat. (just in case you weren't aware). That's the first thing that i'd check if your 3pt hitch arms aren't going down. 2018 JD 1025r, 54" mower deck, backhoe, front-end-loader, Braber Equipment post hole auger, 9 and 12" augers, 1999 +/- Craftsman lawn ...However, the John Deere 1010 has several issues. Uneven engine running, improper steering, overheating issues are a few of the most common problems suffered by John Deere 1010. Every tractor suffers from some problems as they consist of many working parts, they ought to suffer from some problem. This is also the case for John Deere 1010. 6 Most Common Complaints from John Deere 5100m Tractor Users. 1. Diesel Engine Won’t Start. This is the most common complaint we came across. Several reasons contribute to this problem ranging from simple issues such as empty fuel tanks to complicated issues such as jammed fuel injection pumps. In summary, here are some of the potential ... Fuel Pump. The first thing you’ll want to check when troubleshooting a diesel tractor that starts but won’t stay running is the pressure of the fuel pump. Too much or too little pressure within the fuel pump can cause issues. To identify if you have too much pressure inside the fuel pump, you’ll need to conduct a test to allow additional ...Here we will elaborate on John Deere 955’s problems further, explaining the signs and possible reasons behind the issues. People with basic repairing knowledge might fix them independently or know what to do. 1. Oil leaks. Oil leakage on your tractor can be pretty irritating, and it often indicates some deeper internal issues.A tractor mower won’t start if the blade lever/button is on, manual mowers need to be in Neutral gear, and some mowers won’t allow starting if the oil level is low or the hood is open. If you are in any doubt about the correct starting procedure for a lawn tractor, check out – “How to Start Husqvarna Ride-on Mower.” If all that is correct, the problem may well be with the clutch itself and may require a tractor split for repair. On the other hand, the external PTO levers and linkage on many tractors of that series (00, 03, 05, 10) have been changed and improved many times over the course of production with the 00 being the earliest.Mar 26, 2018 · J. Jonnyd Discussion starter · Mar 26, 2018. Hi All, I'm having trouble starting my 5420. The issue started out intermittently where it would fire when turned over and the shutdown immediately. Eventually after a couple of tries or after starting it with the throttle raised it would continue to run and act normal. Jan 8, 2023 · John Deere 345 won’t turn over. I’ve been having some issues with my 345 lately. It is not the plastic gear model. I have the FD611V engine. It turned over weakly several times and then stopped turning over at all. I’ve cleaned all the battery cables and the main ground. I removed the spark plugs and that didn’t help. The most common reason for a no start, not even a click sound, is a totally flat battery, but other likely causes include: Transmission in Drive. Brake Pedal not Pressed. Blade Switch / Lever On. Not Sitting in Seat. Bad Battery Connection. Sensor Faults. Flat / Faulty Battery. Main Fuse Blown.Fuel Pump. The first thing you’ll want to check when troubleshooting a diesel tractor that starts but won’t stay running is the pressure of the fuel pump. Too much or too little pressure within the fuel pump can cause issues. To identify if you have too much pressure inside the fuel pump, you’ll need to conduct a test to allow additional ...With 10 hours of operation after the joystick linkage lube, no 3PH problems so far. So here are two possibilities: Rockshaft bypass valve not closing or a sticking loader joystick selective control valve. Feb 12, 2007 / 3pt won't raise #6.Here we will elaborate on John Deere 955’s problems further, explaining the signs and possible reasons behind the issues. People with basic repairing knowledge might fix them independently or know what to do. 1. Oil leaks. Oil leakage on your tractor can be pretty irritating, and it often indicates some deeper internal issues. Walters owned two tractors then. A Farmall 300 on gasoline and a Farmall C, that had once belonged to his father-in-law, and had been converted from gasoline to LP Gas. Many times, as a small boy, I would cross the fence behind the house my grandparents lived in and walk down the turn row to where granddaddy would be cultivati ... May 29, 2020 · The GT262 is a relatively simple machine, which is in your favor. The entire ignition system is comprised of the stator and a coil. The coils do go bad. They are about $75 new, depending upon which coil you need. You do need to know the specific engine model number you have, which should be on the tag on the engine. What to Do If Your Tractor Won’t Start, Just Clicks. If your John Deere won’t crank and all you hear are clicking sounds when you turn the key, you likely have a bad battery or a bad connection somewhere between the battery and the starter. Double check that the alternator and battery connections are clean and tight. JimR Discussion starter · Apr 19, 2019. So I wheeled my D160 out of the shed to check things over, do an oil change, grease it, etc... before the mowing season starts. It won't run. The engine turns over fine and it will fire up for a few seconds if I shoot starting fluid down the carb throat. But it won't fire up on it's own with a (near ...If you've been out using your tractor and all of a sudden it dies and won't restart, or, if you parked the tractor and left it for awhile and now you're back and it won't start, this video...The Clutch Is Engaged and the PTO Light Is on, but the PTO Shaft Isn’t Turning. If your PTO is mechanical with levers, check the linkage between the hand lever and the clutch. If that is bent, the clutch won’t be able to engage. You can also check to make sure the link that connects the driveshaft to the rear gearbox is not bent or broken ...Fuel Pump. The first thing you’ll want to check when troubleshooting a diesel tractor that starts but won’t stay running is the pressure of the fuel pump. Too much or too little pressure within the fuel pump can cause issues. To identify if you have too much pressure inside the fuel pump, you’ll need to conduct a test to allow additional ...Oct 23, 2014 · See if you can observe the driveshaft while someone else operates the tractor with the lever in the fwd position, you'll at least know whether it's a transmission problem or a front axle problem if not somewhere in between. Also mine has a plastic shroud covering the shaft that had to be removed first. Oct 23, 2014 / 4 wheel drive will not ... Jul 3, 2019 · John Deere GT235 garden tractor. mower (pto) shut off while mowing. Stopped the tractor and shut it off to figure it out and now the tractor won't start. Also, now the pto switch turns the clutch off … read more Sep 12, 2022 · Below is a report documented by a John deere 3046r tractor user. At 6 months old, the three-point hitch quit working (wouldn’t drop even with ballast box attached). Valves, etc., have been replaced numerous times but still won’t work. A dead battery or terminal corrosion Failing engine Whatever the problem is, it is essential to diagnose it first. Then, you can figure out the correct approach for getting your tractor up and running again. Read on to learn more about this topic! Oct 23, 2014 · See if you can observe the driveshaft while someone else operates the tractor with the lever in the fwd position, you'll at least know whether it's a transmission problem or a front axle problem if not somewhere in between. Also mine has a plastic shroud covering the shaft that had to be removed first. Oct 23, 2014 / 4 wheel drive will not ... Mar 9, 2014 · I have a 1985 John Deere 850 Diesel Tractor that won't start. The battery is new & fully charged. Dash lights come on, gearshift, hi/lo, pto are all out of gear. Parking brake set, clutch fully depressed. Seat switch has been bypassed. Aug 7, 2004 · Since one and a half weeks ago my John Deere STX38 lawn tractor wouldn't crank any more. It's about 14 years old, had regular maintenance through our local small engine John Deere dealer, including this spring. The battery shows 12 volts. The engine won't turn over when I turn the ignition switch. The gas line shutoff is turned "on". Walters owned two tractors then. A Farmall 300 on gasoline and a Farmall C, that had once belonged to his father-in-law, and had been converted from gasoline to LP Gas. Many times, as a small boy, I would cross the fence behind the house my grandparents lived in and walk down the turn row to where granddaddy would be cultivati ... Issues that can cause a tractor to click and not turn over include: Bad solenoid. Faulty safety switches. A dead battery or terminal corrosion. Failing engine. Whatever the problem is, it is essential to diagnose it first. Then, you can figure out the correct approach for getting your tractor up and running again.10. Tractor. John Deere 4720. I have a JD 4720 that cranks over but won't start. The last time it ran was two months ago and started just fine at that time. I've done a ton of research on this forum but haven't been able to figure it out. Most common problems have pointed to the solenoid or the thermistor. I tested every relay and checked all ...Posted: Tue May 08, 2018 6:41 am Post subject: John Deere 2020 - Won't Start. Hello. I have a John Deere 2020 gas tractor. The lights on the dash will no light up with I turn the key switch on. I have replaced the key switch; however does not seem like it is getting power somehow. Battery is fully charged. Is this something like the voltage ...John Deere 4066R Deluxe Cab, 440R MSL Loader, AY11E 4-in-1 Bucket, 485A Backhoe John Deere 2032R, Tektite Cab, 220R Loader, 62D Deck, HD60 Snowblower Classen 60RT Aerator, Tarter 60" Tiller, Fimco 60 Gallon 3PH Sprayer, 73" & 57" HD Front BucketsPosted: Fri May 04, 2018 11:17 am Post subject: Re: Power loss and will not rev up. Check the fuel shutoff under the tank. Normally a clogged check valve in the inj. pump return el will cause the tractor to die. almost immediately after startup. Retainer ring particles could be sticking the.Mar 26, 2018 · J. Jonnyd Discussion starter · Mar 26, 2018. Hi All, I'm having trouble starting my 5420. The issue started out intermittently where it would fire when turned over and the shutdown immediately. Eventually after a couple of tries or after starting it with the throttle raised it would continue to run and act normal. May 29, 2020 · The GT262 is a relatively simple machine, which is in your favor. The entire ignition system is comprised of the stator and a coil. The coils do go bad. They are about $75 new, depending upon which coil you need. You do need to know the specific engine model number you have, which should be on the tag on the engine. Disengage the transmission by pulling out the lever. The lever is situated on the back. For a collecting one, take the box off to find the lever. Sit on the seat and start the engine. Move the throttle control to a slow position. Disengage the clutch or brake pedal by keeping motion control levers in neutral. Feb 1, 2009 · Tractor. JD 4310 eHydro, Make sure you have 12v at the starter, could be bad battery cable. The off gassing from the battery eats everything on the 4x00 and 4x10. Feb 1, 2009 / JD 4300 won't crank #10. Jun 21, 2022 · The John Deere X530 is a high-performance lawn tractor known for its reliability and versatility. Designed to tackle various tasks, from mowing large lawns to hauling heavy loads, the X530 is a popular choice among homeowners and professional landscapers alike. Lawn tractor won't start: Diagnosing a no fuel issue TheFritz423 69.7K subscribers Subscribe 136K views 4 years ago John Deere LA120 with a Briggs and Stratton 21 hp OHV Twin, no fuel coming...Lawn tractor won't start: Diagnosing a no fuel issue TheFritz423 69.7K subscribers Subscribe 136K views 4 years ago John Deere LA120 with a Briggs and Stratton 21 hp OHV Twin, no fuel coming...Since one and a half weeks ago my John Deere STX38 lawn tractor wouldn't crank any more. It's about 14 years old, had regular maintenance through our local small engine John Deere dealer, including this spring. The battery shows 12 volts. The engine won't turn over when I turn the ignition switch. The gas line shutoff is turned "on".I have a John Deere diesel tractor that won't start. The battery is fully charged, and the dash lights and headlights are bright. It will not turn over or even "click" like it's trying. There is no clutch starter safety switch, but there is a range shift lever starter safety switch. Is there a way to eliminate this switch or diagnose the problem?The rate of drop knob is located just above the floor boards directly below the operators seat. (just in case you weren't aware). That's the first thing that i'd check if your 3pt hitch arms aren't going down. 2018 JD 1025r, 54" mower deck, backhoe, front-end-loader, Braber Equipment post hole auger, 9 and 12" augers, 1999 +/- Craftsman lawn ...Repair or replace the lift cylinder, piston, control valve, relief valve, hoses, and fittings. Remove and clean the control valve, then reassemble. 3. The Engine Leaks Oil. One of the most pressing problems with John Deere 1020 tractors is engine leaks. The oil seeps from the crankcase and makes a mess underneath the tractor. Jul 13, 2014 · John Deere Tractors. Utility Tractors. 3 Point won't lower. 24879 Views 9 Replies 3 Participants Last post by Zap73, Jul 30, 2014 Jump to Latest Z. Zap73 Discussion ... Transmission Failure. Problems with your mower's transmission can lead to an inability to shift gears, which may prevent your riding mower from driving forward or in reverse. The mower could also become stuck in one gear due to transmission failure or damage. Leaks in the fluid reservoir or any transmission lines can also cause shifting problems. With little effort the tractor now runs and runs pretty well but will not idle down. The governor is responsive throttling up but the only way I can get it to idle back down is by pulling the choke out. I have had the governor shaft out and all looks to be in good shape with little play in the weights. I have also checked the throttle shaft for ...Jan 8, 2023 · John Deere 345 won’t turn over. I’ve been having some issues with my 345 lately. It is not the plastic gear model. I have the FD611V engine. It turned over weakly several times and then stopped turning over at all. I’ve cleaned all the battery cables and the main ground. I removed the spark plugs and that didn’t help. Jan 7, 2023 · 2. No Fuel in the Fuel Tank. John Deere mower fuel tank. Another main reason why your John Deere mower won’t start is if your tank is empty. Empty fuel tanks can halt operations, cause sub-par performance and make rough sounds. It is important to always check your fuel level regularly before you start the machine. Jun 8, 2020 · Probably one of the easiest repairs I've ever done...once I learned from the owner some details about the recent flat tire repair that had been done. Don't o... John Deere recommends replacing the hydraulic fluid after every 50 hours of usage to ensure optimum performance. We recommend doing this because it can result in poor engine and cutting performance. 4. Overheating engine issues. While not a specific problem to the John Deere 5045e, this is undoubtedly something you will encounter and should be ... Sep 7, 2017 · Another good test to isolate the key switch/harness wiring from the battery/starter system is to jump the solenoid to engage the starter. Do this: 1) Disconnect small solenoid wire from the starter. 2) turn key to run position. 3) using a conductor, jump the starter motor battery terminal to the solenoid terminal. John Deere 4066R Deluxe Cab, 440R MSL Loader, AY11E 4-in-1 Bucket, 485A Backhoe John Deere 2032R, Tektite Cab, 220R Loader, 62D Deck, HD60 Snowblower Classen 60RT Aerator, Tarter 60" Tiller, Fimco 60 Gallon 3PH Sprayer, 73" & 57" HD Front BucketsThere can be many reasons why your John Deere tractor will not start. This includes a faulty starter solenoid, damaged battery, clogged fuel filter, problematic spark plugs, and more. These are the most frequent issues that a John Deere can face.Jun 10, 2016 / John Deere Tractor Won't Start. #9. Firstly Tom , never a good idea to bump a thread that is years old even if you have a similar mower & similar problem. Second we need to know which engine you have in the Deere, it helps. Deleve a bit deeper into you manual to the transmission repair section.6 Most Common Complaints from John Deere 5100m Tractor Users. 1. Diesel Engine Won’t Start. This is the most common complaint we came across. Several reasons contribute to this problem ranging from simple issues such as empty fuel tanks to complicated issues such as jammed fuel injection pumps. In summary, here are some of the potential ... May 17, 2018 · Report to Moderator. Posted: Mon Apr 30, 2018 12:49 pm Post subject: Re: John Deere 5210 won't stay running. There are 2 senders located on your thermostat housing, one is for temp, the other goes to the injector pump harness,, unplug the one going to the injector pump, and check the fuse on your circuit board,, the pump sender shorts out and ... Posted: Fri May 04, 2018 11:17 am Post subject: Re: Power loss and will not rev up. Check the fuel shutoff under the tank. Normally a clogged check valve in the inj. pump return el will cause the tractor to die. almost immediately after startup. Retainer ring particles could be sticking the.Here we will elaborate on John Deere 955’s problems further, explaining the signs and possible reasons behind the issues. People with basic repairing knowledge might fix them independently or know what to do. 1. Oil leaks. Oil leakage on your tractor can be pretty irritating, and it often indicates some deeper internal issues. Loader Won't Lift. My father-in-law has a JD 790 with a 419 loader that i've been using to move some dirt around. The loader just up and quit lifting, though the bucket will curl and the three-point works fine. There's fluid going to the barrel side of the rams, but not to the shaft sides. My father-in-law said this happened once before and ...John Deere recommends replacing the hydraulic fluid after every 50 hours of usage to ensure optimum performance. We recommend doing this because it can result in poor engine and cutting performance. 4. Overheating engine issues. While not a specific problem to the John Deere 5045e, this is undoubtedly something you will encounter and should be ... Oct 28, 2020 · My John Deere lawn mower won't stay running.I show you what i do to fix my John Deere (100 series) so it stays running.Hope this helps youThank you very muc... Jul 5, 2017 · 2. A. allicatguy Discussion starter · #4 · Jul 23, 2017. I need your help. The 4100, despite extensive inspections and checks still will not start. The battery is new, the ignition switch replaced and the wiring checked for breaks, loose connections or bad grounds and the relays/switches checked for proper operation. John Deere Tractor Won't Start. I recorded this on my phone, which I normally don't do. Anyway, watch me try to fix the problem preventing my tractor from starting. Be sure to see the surprise at ...If your John Deere won’t crank and all you hear are clicking sounds when you turn the key, you likely have a bad battery or a bad connection somewhere between the battery and the starter. Double check that the alternator and battery connections are clean and tight.1. newbie2 · #4 · Aug 22, 2017 (Edited) Usually when you have to choke to run its starving for fuel somewhere. The main power jet may be clogged or the fuel level in the bowl is too low, fuel filter clogged, port to fuel pump from crank case may be loose. I have run straight sea foam a few times and it worked for me.My X540 lawn tractor wouldn’t start this spring and these are the steps I worked through to ultimately solve my problem. I think trying to jump start the dea...
Technician: J.R. With someone setting on the seat, the brake pedal pressed in and the key turned to the start position you should have power to one of the solenoid terminals. If you have no power then you may have another switch such as the reverse switch bad. If you have power then I would say the solenoid is bad.. Megane lopez
Lawn tractor won't start: Diagnosing a no fuel issue TheFritz423 69.7K subscribers Subscribe 136K views 4 years ago John Deere LA120 with a Briggs and Stratton 21 hp OHV Twin, no fuel coming...John Deere GT235 garden tractor. mower (pto) shut off while mowing. Stopped the tractor and shut it off to figure it out and now the tractor won't start. Also, now the pto switch turns the clutch off … read moreIssues that can cause a tractor to click and not turn over include: Bad solenoid. Faulty safety switches. A dead battery or terminal corrosion. Failing engine. Whatever the problem is, it is essential to diagnose it first. Then, you can figure out the correct approach for getting your tractor up and running again.Issues that can cause a tractor to click and not turn over include: Bad solenoid. Faulty safety switches. A dead battery or terminal corrosion. Failing engine. Whatever the problem is, it is essential to diagnose it first. Then, you can figure out the correct approach for getting your tractor up and running again.The rate of drop knob is located just above the floor boards directly below the operators seat. (just in case you weren't aware). That's the first thing that i'd check if your 3pt hitch arms aren't going down. 2018 JD 1025r, 54" mower deck, backhoe, front-end-loader, Braber Equipment post hole auger, 9 and 12" augers, 1999 +/- Craftsman lawn ...Technician: J.R. With someone setting on the seat, the brake pedal pressed in and the key turned to the start position you should have power to one of the solenoid terminals. If you have no power then you may have another switch such as the reverse switch bad. If you have power then I would say the solenoid is bad.Disconnect the battery negative (black cable) & isolate it. Then remove the black plastic cover on the rear of the starter motor and make sure the connections are tight. If you don't disconnect the battery before doing this, your wrench will make a perfect short circuit. If you start with the positive battery cable...Sep 25, 2021 · This sweet John Deere 318 tractor won't start. Let's fix the ignition and get it back to work!Send us a postcard: Watch Wes WorkP.O. Box 106Fulton, IL 61252S... Sep 12, 2022 · Let’s look at the list of 5 problems that you might face with your John Deere 2032r and their solutions. 1. Engine Won’t Start. Photo by Lee Cannon via Flickr. The trouble could be with the battery if the lawn tractor is challenging to turn on. Inspect to see if the battery is charged and has the expected voltage. Dec 16, 2018 · John Deere 4066R Deluxe Cab, 440R MSL Loader, AY11E 4-in-1 Bucket, 485A Backhoe John Deere 2032R, Tektite Cab, 220R Loader, 62D Deck, HD60 Snowblower Classen 60RT Aerator, Tarter 60" Tiller, Fimco 60 Gallon 3PH Sprayer, 73" & 57" HD Front Buckets Reinstall the filters and close the hood before attempting to start. Check that the John Deere 100 series procedures are being followed. Starting the engine requires that the brake lever is pressed down firmly. Check to make sure the power take off (PTO) for the blades is set in the "Off" position. For the engine to start, the rider has to be ...Apr 19, 2014 · With little effort the tractor now runs and runs pretty well but will not idle down. The governor is responsive throttling up but the only way I can get it to idle back down is by pulling the choke out. I have had the governor shaft out and all looks to be in good shape with little play in the weights. I have also checked the throttle shaft for ... .